BULK HANDLING EQUIPMENT & SYSTEMS

CASE HISTORIES

CASE HISTORIES

 



Print-Ready PDF

 

This story has appeared
in the following publications:


Bulk
Bulk
11/01/2010

What's New In Process Technology
What's New In Process Technology
10/01/2010

Chemical Technology
Chemical Technology
06/01/2010

Canadian Process Equipment & Control News
Canadian Process Equipment & Control News
04/01/2010

Water World
Water World
11/01/2009

Australian Bulk Handling Review
Australian Bulk Handling Review
11/01/2009

Automated Handling of Activated Carbon in Bulk Bags Reduces Dust and Labor for Municipal WTPs

LAFAYETTTE, CO. & SWIFT CURRENT, SASKATCHEWAN, CANADA— Two cities, one in the United States and the other in Canada, over 700 miles (1100 km) apart, were experiencing nearly identical problems caused by manual addition of powdered activated carbon to their municipal water treatment systems. Both cities not only eliminated a health hazard caused by carbon powder dust, but also reduced the amount of labor required to add powdered activated carbon to the system by installing a bulk bag unloading system.

The city of Swift Current draws its municipal water supply from a reservoir formed by a dam on the Swift Current Creek at an average rate of 1.5 million gal (6.8 million l) a day with a peak rate of 5.5 million gal (25 million l) a day. Potassium permanganate is added at a concentration of 1.5 parts per million (ppm), then powdered activated carbon is added in the form of a slurry consisting of 0.13% to 0.47% solids, and the water is gravity fed into a low well at a rate of approximately 25 gal (114 l) per minute. Reaching a final concentration of 20 ppm, the carbon's function is to adsorb organic materials, eliminating unwanted tastes and odors.

After addition of liquid alum, sludge conditioners, and polymers in the clarifier, filtered water is pumped to a clear well located at the water treatment facility with a capacity of 180,000 gal (820,000 l) and to two reservoirs within the city itself, each holding 1.5 million gal (6.8 million l), for distribution to residents of the city of Swift Current.

The city of Lafayette draws its water from two local reservoirs formed by dams on the Boulder Creek and from one reservoir on the South Boulder Creek. Consumption is approximately 2 million gal (7.5 million l) per day during the winter, but can reach as much as 10 million gal (38 million l) per day during the summer months. From the reservoirs, water flows into an onsite aeration and flocculation facility similar to that used by the city of Swift Current, where powdered activated carbon and other treatment chemicals are added. After final filtration, the water is pumped into three storage tanks, which together can hold up to 13 million gal (53 million l) of water, for distribution to residents of the city of Lafayette.


Powdered activated carbon was added manually

Prior to the installation of the bulk bag unloading systems, operators at both facilities were emptying 35-45 lb (16-20 kg) bags of powdered activated carbon generating carbon dust and putting physical strain on workers.

Powdered activated carbon is an extremely fine powder with an average particle size of only 20 microns and a bulk density of 21.5 lb/ cu ft (34.4 kg/cu m). "The slightest air movement causes carbon dust everywhere, and it cakes and smears on everything it touches, including your clothes and your skin," says Rudy Holland, city of Swift Current Superintendent of Water Treatment.

"We tried using a dust collection system, but it never worked properly," says Holland. Also, the capacity of the system was limited by the small screw feeder, which took 16 hours to transfer the powdered carbon from the 1000 lb (450 kg) capacity hopper into the liquid slurry eductor. Since the water treatment facility operates only one shift a day — staffed for 8-1/2 hours, then unmanned and controlled by computer for 15-1/2 hours — the hopper, if not completely filled at the beginning of the unmanned shift, could potentially run out of carbon when personnel were not present to refill it."

City of Swift Current operators were opening and emptying as many as twenty five 45-55 lb (23-25 kg) bags of powdered activated carbon a day into the hopper. City of Lafayette operators were carrying a 35-40 lb (16-18 kg) bag of powdered carbon up a set of metal stairs and emptying it directly into the aeration and flocculation facility. "This not only created hazardous carbon dust, but since we used about 2 to 4 bags a day during the winter and as many as 10 to 17 bags a day during the summer, it also required extensive manual labor and placed operators working alone on the midnight shift in danger of falling and injuring themselves," explains Ed Zimbleman, Lead Operator. "In addition, bags would occasionally break, requiring operators to hose down the entire area."


Bulk bag unloading and feeding systems eliminate hazards

At both facilities, installation of an automated bulk bag unloading and feeding system eliminated dust caused by untying, discharging, collapsing and removing individual small bags while increasing operator safety and reducing manual labor.

The city of Swift Current now purchases 1100 lb (500 kg) bags and unloads 1 to 3.5 bags per week. The city of Lafayette unloads between one 900 lb (408 kg) bulk bag per week during the winter and as many as 4.5 bags per week during the peak summer months.

The Flexicon bulk bag dischargers incorporate devices that contain dust and promote complete discharge. A manual SPOUT-LOCK® clamp ring is raised pneumatically by a TELE-TUBE® telescoping tube, allowing an operator to make a high-integrity, dust-tight connection with the bag spout. The telescoping tube is then released to exert continuous downward tension on the clamp ring and, in turn the bag spout, which elongates the bag as it empties to promote complete discharge.

Flow is additionally promoted by FLOW-FLEXER® pneumatically actuated plates that raise and lower opposite bottom edges of the bag, causing the activated carbon to flow into and through the bag spout.

A POWER-CINCHER® flow control valve encircles the upper portion of the bag spout, allowing gradual discharge once the drawstring is untied, as well as retying of partially empty bags.

Mounted on the side of both unloading frames is a BAG-VAC® dust collector that draws displaced air and dust from a hopper vent during discharge, and collapses empty bags dust-free, ready for tie-off and removal.


Two systems have important differences

At the city of Swift Current, a hoist from a 24 ft (7 m) high ceiling-mounted monorail loads a 1100 lb (500 kg) bag onto a 5 ft (1.5 m) high half-frame bulk bag discharger mounted on a 6.5 ft (2 m) high platform. The discharger frame is integrated with a 10 ft (3 m) high frame that holds a 2000 lb (900 kg) capacity hopper (for the contents of two bags), a twin-screw volumetric feeder, washdown hopper, and liquid slurry eductor. The powdered activated carbon flows from the bulk bag to the hopper and then to the feeder which meters it into the washdown hopper and eductor to blend with the 25 gpm (114 l per min) water streaming toward the low well. A control panel regulates the dust collector, the bag activators, feeder, and flow-promoting air pads on the side of the hopper.



Forklift loading replaces manual emptying of bags

At the city of Lafayette an operator forklift-loads a 900 lb (114 kg) bag in a lifting frame onto a full-height 9.75 ft (3 m) high discharger. The powdered carbon flows through the telescoping tube and 2 ft (0.6 m) long downspouting which extends through the floor to a 5 cu ft (0.14 cu m) capacity receiving hopper contained in a 7 ft (2.1 m) high frame which also holds the twin screw volumetric feeder, washdown hopper, and liquid slurry eductor. Controls govern the dust collector, feeder, and air fluidizers for hopper flow, and notify the operator to change empty bags.

Continuous blending of powdered activated carbon from the volumetric feeder with fresh water creates a slurry, consisting of as little as 0.006% solids in the winter to as much as 0.05% solids in the summer. It is added to the clarifier at a rate of 120 gal (450 l) per minute, resulting in a final carbon concentration of 5 to 7 ppm. "We basically just set it and forget it," says Zimbleman.


Design and installation a team effort

The City of Swift Current system was designed by a local consultant in Regina, SK, with the help of Mequipco Ltd. that supplied the equipment, and was installed by a local Saskatchewan contractor. Mequipco Ltd. (www.mequipco.com) is a manufacturer's representative, equipment supplier and systems integrator based in Calgary, Alberta whose primary focus is on mechanical equipment for water and wastewater treatment. Dan Landry and Kevin Dickinson headed the Mequipco team that assisted with the system startup and design.

The City of Lafayette system was designed and installed by Flexicon Corp. (www.flexicon.com) and Process Control Equipment Co. (www.pcecompany.com), a manufacturer's representative firm headquartered in Lehi, Utah specializing in material handling equipment for powder and granule processing. Susan Aberle of the company's Wheat Ridge, CO regional office assisted with installation and startup.

"We evaluated two other machines in addition to the Flexicon system," says Zimbleman. "Although they were similar, the other two manufacturers were unwilling to make the necessary physical modifications to our facility, including cutting a hole in a concrete floor in order to put the hopper on top of the feeder."

Several modifications were made after the system was installed. "We were having problems with the washdown hopper clogging from time to time," Zimbleman explains. "The hopper is 2 feet (0.6 m) high and 2 feet (0.6 m) in diameter at the top, but only 6 inches (15 cm) in diameter at the bottom. Susan and her team added jets with plastic nipples so the water circulated around the hopper instead of just spraying into it, which eliminated the problem."

Click to enlarge

City of Lafayette operator forklift-loads bag-lifting frame onto bulk bag discharger.


Click to enlarge

Upper level: Bulk bag discharger with control panel and BAG-VAC® dust collector.


Click to enlarge

Lower level: Frame holds 5 cu ft (0.14 cu m) capacity receiving hopper from which a volumetric feeder meters powder carbon to a washdown hopper and liquid slurry eductor where the carbon blends with fresh water (green tube) flowing to the clarifier.


Click to enlarge

Bulk bag is suspended from a lifting frame that rests in receiving cups atop each of four frame posts. Pneumatically-actuated FLOW-FLEXER® plates beneath the left and right bottom edges of the bag hinge up and down at timed intervals to loosen compacted materials and raise the bottom of the bag into a steep V shape, promoting total discharge through the bag spout.


Click to enlarge

A SPOUT-LOCK® clamp ring creates a high integrity seal between the bag spout and a TELE-TUBE® telescoping tube that maintains constant downward tension on the bag, promoting complete, dust-free discharge.


Click to enlarge

The airtight system features a side- mounted BAG-VAC® dust collector that draws displaced air and dust from the hopper and collapses empty bags dust-free.


Click to enlarge

Operator inspects powdered carbon entering the washdown hopper.


Click to enlarge

Water flows from the sedimentation basin, through the powdered carbon addition system, and into the distribution system.


Click to enlarge

At City of Swift Current, bag is loaded onto half-frame bulk bag discharger from ceiling-mounted monorail. The frame below the discharger incorporates a 2000 lb (900 kg) capacity hopper, volumetric feeder, washdown hopper, and a liquid slurry eductor that draws carbon powder into a water stream.


Click to enlarge

Bottom frame consolidates a receiving hopper, volumetric feeder, washdown hopper, and liquid slurry eductor.